TEMPERATURE

This unit is designed for indoor use

OPERATING

32° to 104° F (0° to 40° C)

only. Select a location sturdy enough to

STORAGE

5° to 113° F (-15°to 45° C) charge the UPS

handle the weight.

battery every six months

Do not operate the UPS where there is

MAXIMUM

excessive dust or the temperature and

ELEVATION

humidity are outside the specified limits.

OPERATING

10,000 ft (3,000 m)

Ensure that the air vents on the front

STORAGE

50,000 ft (15,240 m)

and rear of the UPS are not blocked.

HUMIDITY

0 to 95% relative humidity

WEIGHT

UPS

120 lbs (55 kg)

UPS WITH

140 lbs (64 kg)

PACKAGING

.

1

Power management software and interface kits can be used with the UPS.

serial com

Use only interface kits supplied or approved by APC.

Any other serial interface cable will be incompatible with the UPS

connector.

Manual bypass enables the user to manually put connected equipment into

bypass mode.

normal bypass

Emergency Power Off terminal allows the user to connect the UPS to the

central EPO system.

EPO terminal

The UPS features a transient voltage surge-suppression(TVSS) screw for

connecting the ground lead on surge suppression devices such as telephone

TVSS screw

and network line protectors.

When connecting grounding cable, disconnect the unit from the utility

power outlet.

Optional external battery packs provide extended runtime during power

outages. These units support up to ten external battery packs.

external battery

See the APC Web site, www.apc.com for the information on the external

pack connector

battery pack, SURT192XLBP.

5000/6000 VA

XLI models

Load

SMART-UPS RT FRONTDISPLAY

Battery Charge

Indicator

Description

Online

The Online LED illuminates when the UPS is drawing utility power and performing

double conversion to supply power to connected equipment.

On Battery

The UPS is supplying battery power to the connected equipment.

Bypass

The Bypass LED illuminates indicating that the UPS is in bypass mode. Utility

power is sent directly to connected equipment during bypass mode operation.

Bypass mode operation is the result of an internal UPS fault, an overload condition

or a user initiated command either through an accessory or the manual bypass

switch. Battery operation is not available while the UPS is in bypass mode. Refer to

Troubleshooting in this manual.

Fault

The UPS detects an internal fault.

Refer to Troubleshooting in this manual.

Overload

An overload condition exists. See Troubleshooting.

Replace

The battery is disconnected or must be replaced. See Troubleshooting.

Battery

Feature

Function

Power On

Press this button to turn on the UPS. (See below for additional capabilities.)

Power Off

Press this button to turn off the UPS.

Feature

Function

Cold Start

When there is no utility power and the UPS is off, press and hold the

button to

power up the UPS and connected equipment.

The UPS will emit two beeps. During the second beep, release the button.

Self-Test

Automatic: The UPS performs aself-testautomatically when turned on, and every

two weeks thereafter (by default). During the self-test,the UPS briefly operates the

connected equipment on battery.

Manual: Press and hold the

button for a few seconds to initiate the self-test.

Diagnostic Utility Voltage

The UPS has a diagnostic feature that displays the utility voltage. Plug

the UPS into the normal utility power.

The UPS starts a self-testas part of this procedure. Theself-test

does not affect the voltage display.

Press and hold the

button to view the utility voltage bar graph

display. After a few seconds the five-LED,Battery Charge

display

on the right of the front panel shows the utility input voltage.

Refer to the figure at left for the voltage reading (values are not listed

on the UPS).

The display indicates the voltage is between the displayed value on the

list and the next higher value.

FUNCTION

FACTORY

USERSELECTABLE

DESCRIPTION

DEFAULT

CHOICES

Automatic Self-Test

Every 14 days

Every 7 days(168 hours),

Set the interval at which the

(336 hours)

14 days (336 hours)

UPS will execute a self-test.

On Startup Only,

No Self-Test

UPS ID

UPS_IDEN

Up to eight characters to

Uniquely identify the UPS, (i.e.

define the UPS

server name or location) for

network management purposes.

Date of Last Battery

Manufacture Date

Date of

Reset this date when you replace

Replacement

Battery Replacement

the battery modules.

mm/dd/yy

Minimum Capacity

0 percent

0, 15, 25, 35, 50, 60, 75,

Following a low-battery

Before Return from

90 percent

shutdown, the battery modules

Shutdown

will be charged to the specified

percentage before powering

connected equipment.

Alarm Delay After

5 second delay

5 or 30 second delay

Mute ongoing alarms or disable

Line Failure

At Low Battery

all alarms permanently.

Never

Shutdown Delay

20 seconds

0, 20, 60, 120, 240, 480,

Set the interval between the time

720, 960 seconds

when the UPS receives a

shutdown command and the

actual shutdown.

Duration of

2 minutes

2, 5, 7, 10, 12, 15, 18,

The low battery warning beeps

Low Battery Warning.

PowerChute

20 minutes

are continuous when two

software provides

minutes of run time remain.

automatic,

Change the warning interval

unattended

default to a higher setting if the

shutdown when

operating system requires a

approximately 2

longer interval for shutdown.

minutes of battery

operated runtime

remains.

Synchronized Turn-on

0 seconds

0, 20, 60, 120, 240, 480,

The UPS will wait the specified

Delay

720, 960 seconds

time after the return of utility

power before turn-on(to avoid

branch circuit overload).

High Bypass Point

+10% of

+5%, +10%, +15%,

Maximum voltage that the UPS

output voltage

+20%

will pass to connected

setting

equipment during internal

bypass operation.